Angewandte Standards

• DIN 16742 – Plastics moulded parts – Tolerances and acceptance conditions
• ISO 14405 – Geometrical product specifications (GPS)
• ISO 2768-2 – General geometrical tolerances
• BMW_gs90015 -Tolerancing of surfaces, trim areas, hole and cylinder positions
• ATE N 113 63.00 – Plastics mouldings; Tolerances and acceptance conditions for linear dimensions
• DIN 16901 – Plastics mouldings; Tolerances and acceptance conditions for linear dimensions
• DIN 6930 – Steel stampings
• DIN 7168 – General dimension tolerances for iron and steel castings
• DIN 861 – Table of tolerances for gauge blocks according to DIN 861
• DIN EN ISO 8015 – Geometrical product specifications (GPS) – Fundamentals – Concepts, principles and rules (ISO 8015:2011)
• DIN ISO 8992 – Fasteners – General requirements for bolts, screws, studs and nuts (ISO 8992:2005)
• DIN 5480-1 – Involute splines based on reference diameters – Part 1: General
• DIN EN 10243-1 – steel die forging – tolerances on dimensions – Part 1: Drop and vertical press forgings
• ISO 286-1 – ISO System of limits and fits: bases of tolerances, deviations and fits
• ISO 1101 – Geometrical tolerancing
• ISO 1660 – Dimensioning and tolerancing of profiles
• ISO 2692 – Maximum material requirement, least material requirement, reciprocity requirement
• ISO 3040 – Dimensioning and tolerancing of cones
• ISO 4291- Methods for the assessment of departures from roundness: measurement of variations in radius
• ISO 4292 – Methods for the assessment of departures from roundness: measurement by two- and three-point methods
• ISO 5458 – Geometrical tolerancing: positional tolerancing
• ISO 5459 – Datums and datum systems for geometrical tolerancing
• ISO TR 5460 – Geometrical tolerancing: tolerancing of form, orientation, location and run-out; verification principles and methods; guidelines
• ISO 6318 – Measurement of roundness: terms, definitions and parameters of roundness
• ISO 7083 – Symbols for geometrical tolerancing: proportions and dimensions
• ISO 8015 – Fundamental tolerancing principle
• ISO 10 360-1 – Coordinate metrology Part 1 definitions and applications of the fundamental geometric principles
• ISO 10 578 – Projected tolerance zone
• ISO 10 579 – Dimensioning and tolerancing: non-rigid parts
• ISO 12 181 – Measurement of roundness deviations
• ISO 12 180 – Measurement of cylindricity deviations
• ISO 12 780 – Measurement of straightness deviations
• ISO 12 781 – Measurement of flatness deviations
• ISO 13 715 – Edges of undefined shape
• ISO 14 253-1 – GPS, decision rules for proving conformance
• ISO 14 253-2 – GPS, guide to the estimation of uncertainty (in preparation)
• ISO TR 14 638 – GPS Masterplan
• ISO 14 660-1 – GPS, geometrical features; general terms and definitions
• ISO 14 660-2 – Extracted median line, median surface, local size
• ISO 15 530-1 – CMM, determining measurement uncertainty, overview
• ISO 15 530-2 – CMM, determining measurement uncertainty, use of multiple measurement strategies
• ISO 15 530-3 – CMM, determining measurement uncertainty, use of calibrated workpieces
• ISO 15 530-4 – CMM, determining measurement uncertainty, use of computer simulation
• ISO 15 530-5 – CMM, determining measurement uncertainty, use of expert judgement
• ISO TR 16 570 – Linear and angular dimensioning and tolerancing: +/- limit specifications – step dimensions, distances, angular sizes and radii
• ISO TS 17 450-1 – Model for GPS, features, characteristics, operation, specification, verification
• ISO TS 17 450-2 – Operators and uncertainties
• VIM – International Vocabulary of Basic and General Terms in Metrology
• GUM – Guide to the expression of uncertainty in measurement
• ASME Y14.5M – 1994 – Dimensioning and tolerancing
• ANSI B89.3.1 – 1972 – Measurement of out-of-roundness
• BS 308 P.3 – Engineering drawing practice, geometrical tolerancing
• BS 3730 – Assessment of departures from roundness
• BS 7172 – British Standard guide to assessment of position, size and departure from nominal form of geometric features
• BS 8888 – Technical product specification (TPS): specification
• DIN 4760 – Form deviation, waviness, surface roughness; system of order, terms and definitions
• DIN 6784 – Edges of workpieces; terms, drawing indications
• DIN 7167 – Relationship between dimensional tolerances and form and parallelism tolerances; envelope requirement without indication
• DIN 7184 – Geometrical tolerances; definitions and drawing indications
• DIN 7186 T.1 – Statistical tolerancing; definitions, applications, drawing indications
• DIN 8570 T.3 – General geometrical tolerances for welded parts
• DIN 40680 T.2 – General form tolerances for ceramic parts in electrical application
• DIN 32 880-1 – Coordinate measuring technique; geometrical basics and terms
• VDI/VDE 2601 T.1 – Requirements on the surface structure to cover function capability of surfaces manufactured by cutting; list of parameters
• TGL 39 092 – Methods of measuring geometrical deviations: general principles
• TGL 39 093 – Methods of measuring deviations from straightness
• TGL 39 094 – Methods of measuring deviations from flatness
• TGL 39 095 – Methods of measuring deviations from parallelism
• TGL 39 096 – Methods of measuring deviations from roundness
• TGL 39 097 – Methods of measuring deviations from cylindricity
• TGL 39 098 – Methods of measuring deviations of the longitudinal section profile
• TGL 43 041 – Methods of measuring straightness deviations of axes
• TGL 43 042 – Methods of measuring deviations from coaxiality
• TGL 43 043 – Methods of measuring the radial run-out deviations
• TGL 43 044 – Methods of measuring the axial run-out deviations
• TGL 43 045 – Methods of measuring the run-out deviations in a given direction
• TGL 43 529 – Methods of measuring the radial total run-out deviations
• TGL 43 530 – Methods of measuring the axial total run-out deviations
• ST RGW 301-76 – Geometrical tolerances: fundamental terms
• ST RGW 368-76 – Geometrical tolerances: drawing indications
• DBL 5404
• DBL 7384
• DIN 53435
• DIN 53497
• DIN 75220
• EN ISO 11357-2,-3,-6
• EN ISO 1172
• EN ISO 1183-1
• EN ISO 3451
• EN ISO 75
• FMVSS 302 VDA 19
• Ford WSS-M2P188-B1
• ISO 105-B06
• ISO 1133
• ISO 16232
• ISO 1625-5
• ISO 179
• ISO 307
• ISO 48-4
• ISO 4892-2
• ISO 527
• ISO 868
• PV 1303
• PV 3929
• PV 3930
• TL 1010
• TL 226
• UL 94
• Volvo STD 1026,8177
• VW PV 3925 e.t.c.